Rendered Foam Walls

This addendum was added to an original Post from 2014 as there has been a lot of publicity recently (late February 2019) about foam panels and certification has been removed from certain types of panels.

A particular issue for apartment blocks has been related to high speed spread across the surface of the panels to other flats.

On a standard house the render should protect the insulation from external flames. (If flames penetrate the plasterboard, from the inside, it is likely that the occupants will either have already evacuated, or be dead before the insulation ignites) n

Nevertheless you should review whether the potential risks from foam panels are acceptable to you.

Original Article

Rendered Foam walls are becoming much more common, particularly in the upper floor of 2 storey homes. They offer a real advantage in situations where it would be difficult to provide adequate suppport for a heavy brick wall (For example when the upper floor needs to be set back from the ground floor)

If you are worried about strength you need to be aware that the real strength of the house is in the frame. (see: House Construction – The Frame)

Construction

  • The Foam boards, which are manufactured with an external mesh face, are fixed to the frame with special galvanised screws that incorporate spreader washers.
  • Joints are sealed with a polyurethane foam and have mesh jointing tape.
  • External corners are reinforced with metal strips.
  • A minimum of 5mm of  acrylic render  is applied, normally in a three layer system.

Polystyrene Foam

There are 2 different types of foam used in this construction method:

  • Expanded polystyrene( EPS) – Good thermal performance but limited impact resistance/structural strength.
  • Extruded polystyrene (XPS) – Similar thermal performance and looks similar  but the production method is different which results in increased impact resistance and structural strength. Higher cost

Insulation values for the various board thicknesses are:

  • 50mm    – R 1.2
  • 75mm    – R 1.8
  • 100mm – R 2.4

Final Thoughts

Although there are some advantages in this system it does require careful detailing and construction otherwise leakage can occur damaging your house.

The advantage of masonry on the lower part of the house is that it is less likely to be damaged by the bumps and bangs of daily life. Once the wall is above head height damage becomes less of an issue and the rendered foam board should be fine.

I’d prefer XPS to EPS.

Although the insulation values are good the builder will most likely want to save the cost of the insulation batts in the frame. If you ask for the wall to include insulation batts you will have an exceptionally well insulated wall at very little extra cost.

 

For similar posts see Insulation

For more about house design see Choosing a House . . . A new E-book for only $4 to help plan your new house

 

4 Comments

  1. Alex

    I would also like other issues with foam insulation to the topic below:

    – even if foam is fire protected, it may use HBCD as a fire retardant which is extremely carcinogenic and this is why HBCD-based foam insulation has been banned in Europe and US (https://en.wikipedia.org/wiki/Hexabromocyclododecane). Not a lot of manufacturers are readily providing MSDS for the materials their supply and some of them even prefer not to specify fire retardants being used.

    – foam insulation is only semi-vapor permeable and has zero hygroscopicity and therefore, has terrible moisture control properties: can easily lead to issues like mold, rot and cause structural damage to studs (vapor traveling from the “warm” inside to the “cold” outside condensates on the studs);

    – termites and ants can chew through the foam insulation;

    1. Brian Ashworth (Post author)

      Thanks for the comments
      Brian

  2. Danielle Robertson

    Hi, I’m cobsidering purchasing a double story home with the entire exterior made from rendered foam brick cladding. What are the pros and cons?

    1. Brian Ashworth (Post author)

      I think the pros are that it offers great insulation.

      The cons are:
      Limited resistance to impact damage
      Bad detail can result in unsightly cracks that increase the risk of water penetration.

Comments are closed.